Nibe Heatpump Binding

The Nibe Heatpump binding is used to get live data from from Nibe heat pumps without using expensive MODBUS40 adapter. This binding should be compatible at least the F750, F1145 and F1245 heat pump models.

The binding support data telegrams (contains max 20 registers) from the heat pump, but binding can also read other registers from the pump. It's recommend to add most changed variables to telegram, binding will then read all other registers automatically from the pump when channels are linked to item. Register reading need to be enabled from the thing configuration. Binding have also experimental support for register writing. This can be used to configure heat pump. Write mode need to enabled from thing configuration and for safety reason all register identifiers need to explicitly defined.

Supported Things

This binding supports direct serial port connection (RS-485 adapter needed) to heat pump but also UDP connection via NibeGW software.

Thing typeDescription
f1x45-serialSerial port connected F1145 and F1245 Heat Pumps
f1x45-udpUDP connected Nibe F1145 and F1245 Heat Pumps
f1x45-simulatorSimulator for Nibe F1145 and F1245 Heat Pumps
f750-serialSerial port connected F750 Heat Pumps
f750-udpUDP connected Nibe F750 Heat Pumps
f750-simulatorSimulator for Nibe F750 Heat Pumps

Discovery

Discovery is not supported, therefore binding and things need to be configured via Paper UI or thing files.

Prerequisites

When Modbus adapter support is enabled from the heat pump UI, the heat pump will start to send telegrams every now and then. A telegram contains a maximum of 20 registers. Those 20 registers can be configured via the Nibe ModbusManager application.

Unfortunately Nibe has made this tricky: telegram from heat pump should be acknowledged, otherwise heat pump will raise an alarm and go in alarm state. Acknowledge (ACK or NAK) should be sent accurately. Binding support also direct serial port connections to heat pump, but heat pump will raise an alarm when openHAB binding not running e.g. during openHAB updates. This problem can be resolved by using the nibegw program, which can be run on Unix/Linux (such as a Raspberry Pi) or Arduino-based boards. If you are running openHAB on Raspberry Pi nibegw program can run also on the same machine, then when openHAB is not running nibegw will still acknowledge packets to heat pump. Obviously, this doesn't solve the problem when whole Raspberry Pi is down, therefore Arduino based solution is recommended.

nibegw is an application that read telegrams from a serial port (which requires an RS-485 adapter), sends ACK/NAK to the heat pump and relays untouched telegrams to openHAB via UDP packets. The Nibe Heat Pump binding will listen to a UDP port and parse register data from UDP telegrams.

Arduino

Arduino-based solution is tested with Arduino uno + RS485 and Ethernet shields. Also ProDiNo NetBoards are supported. ProDiNo have both Ethernet and RS-485 ports on the board.

Arduino code is available here

Arduino code can be builded via Arduino IDE. See more details from www.arduino.cc. NibeGW configuration(such IP addresses, ports, etc) can be adapted directly editing the code files.

Raspberry Pi (or other Linux/Unix based boards)

C code is available on here

build C code:

gcc -std=gnu99 -o nibegw nibegw.c

help:

nibegw -h

./nibegw usage:

    -h                 Print help
    -v                 Print debug information
    -d <device name>   Serial port device (default: /dev/ttyS0)
    -a <address>       Remote host address (default: 127.0.0.1)
    -p <port>          Remote UDP port (default: 9999)
    -f                 Disable flow control (default: HW)
    -r <address>       RS-485 address to listen (default: 0x20)
    -i                 Send all messages by UDP (default: only modbus data)
    -n                 Don't send acknowledge at all
    -o                 Send acknowledge to all addresses
    -t                 Test mode
    -l <port>          Local UDP port for read commands (default: 9999)
    -w <port>          Local UDP port for write commands (default: 10000)
    -q                 Print data in log format

run example:

nibegw -v -d /dev/ttyUSB0 -a 192.168.1.10

Binding Configuration

No binding configuration required.

Thing Configuration

Things can be fully configured via Paper Ui, but following information is usefull if you want to configure things via thing configuration files.

UDP connection

Thing examples:

nibeheatpump:f1x45-udp:myPump [hostName="192.168.1.50", port=9999]
nibeheatpump:f1x45-udp:myPump [hostName="192.168.1.50", port=9999, readCommandsPort=10000, writeCommandsPort=10001, refreshInterval=30, enableReadCommands=true, enableWriteCommands=true, enableRegistersForWriteCommands="44266, 47004"]

All supported configuration parameters for UDP connection:

PropertyTypeDefaultRequiredDescription
hostNameStringYesNetwork address of the Nibe heat pump
portInteger9999NoUDP port to listening data packets from the NibeGW
readCommandsPortInteger9999NoUDP port to send read commands to the NibeGW
writeCommandsPortInteger10000NoUDP port to send write commands to the NibeGW
refreshIntervalInteger60NoStates how often a refresh shall occur in seconds
enableReadCommandsBooleanfalseNoEnable read commands to read additional variable from Nibe heat pump which are not included to data readout messages. This is experimental feature, use it at your own risk!
enableWriteCommandsBooleanfalseNoEnable write commands to change Nibe heat pump settings. This is experimental feature, use it at your own risk!
enableRegistersForWriteCommandsStringNoComma separated list of registers, which are allowed to write to Nibe heat pump. E.g. 44266, 47004

Serial port connection

Thing example:

nibeheatpump:f1x45-serial:myPump [serialPort="/dev/ttyUSB0"]

All supported configuration parameters for serial port connection:

PropertyTypeDefaultRequiredDescription
serialPortStringYesNetwork address of the Nibe heat pump
refreshIntervalInteger60NoStates how often a refresh shall occur in seconds
enableReadCommandsBooleanfalseNoEnable read commands to read additional variable from Nibe heat pump which are not included to data readout messages. This is experimental feature, use it at your own risk!
enableWriteCommandsBooleanfalseNoEnable write commands to change Nibe heat pump settings. This is experimental feature, use it at your own risk!
enableRegistersForWriteCommandsStringNoComma separated list of registers, which are allowed to write to Nibe heat pump. E.g. 44266, 47004
sendAckToMODBUS40BooleantrueNoBinding emulates MODBUS40 device and send protocol acknowledges to heat pump
sendAckToRMU40BooleanfalseNoBinding emulates RMU40 device and send protocol acknowledges to heat pump
sendAckToSMS40BooleanfalseNoBinding emulates SMS40 device and send protocol acknowledges to heat pump

Channels

This binding currently supports following channels for F1x45 pump models:

Channel Type IDItem TypeMinMaxTypeDescriptionValues
40004Number-3276732767SettingBT1 Outdoor temp
40005Number-3276732767SettingEP23-BT2 Supply temp S4
40006Number-3276732767SettingEP22-BT2 Supply temp S3
40007Number-3276732767SettingEP21-BT2 Supply temp S2
40008Number-3276732767SettingBT2 Supply temp S1
40012Number-3276732767SettingEB100-EP14-BT3 Return temp
40013Number-3276732767SettingBT7 Hot Water top
40014Number-3276732767SettingBT6 Hot Water load
40015Number-3276732767SettingEB100-EP14-BT10 Brine in temp
40016Number-3276732767SettingEB100-EP14-BT11 Brine out temp
40017Number-3276732767SettingEB100-EP14-BT12 Cond. out
40018Number-3276732767SettingEB100-EP14-BT14 Hot gas temp
40019Number-3276732767SettingEB100-EP14-BT15 Liquid line
40022Number-3276732767SettingEB100-EP14-BT17 Suction
40025Number-3276732767SettingEB100-BT20 Exhaust air temp. 1
40026Number-3276732767SettingEB100-BT21 Vented air temp. 1
40028Number-3276732767SettingAZ1-BT26 Temp Collector in FLM 1
40029Number-3276732767SettingAZ1-BT27 Temp Collector out FLM 1
40030Number-3276732767SettingEP23-BT50 Room Temp S4
40031Number-3276732767SettingEP22-BT50 Room Temp S3
40032Number-3276732767SettingEP21-BT50 Room Temp S2
40033Number-3276732767SettingBT50 Room Temp S1
40042Number-3276732767SettingCL11-BT51 Pool 1 Temp
40043Number-3276732767SettingEP8-BT53 Solar Panel Temp
40044Number-3276732767SettingEP8-BT54 Solar Load Temp
40045Number-3276732767SettingEQ1-BT64 Cool Supply Temp
40046Number-3276732767SettingEQ1-BT65 Cool Return Temp
40054Number-3276732767SettingEB100-FD1 Temperature limiter
40067Number-3276732767SettingBT1 Average
40070Number-3276732767SettingEM1-BT52 Boiler temperature
40071Number-3276732767SettingBT25 external supply temp
40072Number-3276732767SettingBF1 Flow
40074Number-3276732767SettingEB100-FR1 Anode Status
40079Number-21474836482147483647SettingEB100-BE3 Current Phase 3
40081Number-21474836482147483647SettingEB100-BE2 Current Phase 2
40083Number-21474836482147483647SettingEB100-BE1 Current Phase 1
40106Number-3276732767SettingCL12-BT51 Pool 2 Temp
40107Number-3276732767SettingEB100-BT20 Exhaust air temp. 4
40108Number-3276732767SettingEB100-BT20 Exhaust air temp. 3
40109Number-3276732767SettingEB100-BT20 Exhaust air temp. 2
40110Number-3276732767SettingEB100-BT21 Vented air temp. 4
40111Number-3276732767SettingEB100-BT21 Vented air temp. 3
40112Number-3276732767SettingEB100-BT21 Vented air temp. 2
40113Number-3276732767SettingAZ4-BT26 Temp Collector in FLM 4
40114Number-3276732767SettingAZ3-BT26 Temp Collector in FLM 3
40115Number-3276732767SettingAZ2-BT26 Temp Collector in FLM 2
40116Number-3276732767SettingAZ4-BT27 Temp Collector out FLM 4
40117Number-3276732767SettingAZ3-BT27 Temp Collector out FLM 3
40118Number-3276732767SettingAZ2-BT27 Temp Collector out FLM 2
40127Number-3276732767SettingEP23-BT3 Return temp S4
40128Number-3276732767SettingEP22-BT3 Return temp S3
40129Number-3276732767SettingEP21-BT3 Return temp S2
40155Number-3276732767SettingEQ1-BT57 Collector temp.
40156Number-3276732767SettingEQ1-BT75 Heatdump temp.
43001Number065535SettingSoftware version
43005Number-3000030000SettingDegree Minutes
43006Number-3276732767SettingCalculated Supply Temperature S4
43007Number-3276732767SettingCalculated Supply Temperature S3
43008Number-3276732767SettingCalculated Supply Temperature S2
43009Number-3276732767SettingCalculated Supply Temperature S1
43013String0255SettingFreeze Protection Status1=Freeze protection active
43024String0255SettingStatus Cooling0=Off, 1=On
43081Number09999999SettingTot. op.time add.
43084Number-3276732767SettingInt. el.add. Power
43086String0255SettingPrio10=Off, 20=Hot Water, 30=Heat, 40=Pool, 41=Pool 2, 50=Transfer, 60=Cooling
43091Number0255SettingInt. el.add. State
43097String0255SettingStatus of the shunt controlled additional heat accessory10=Off, 20=Running, 30=Passive
43103Number0255SettingHPAC state
43108Number0255SettingFan speed current
43152Number0255SettingInternal cooling blocked
43158Number0255SettingExternal adjustment activated via input S4
43159Number0255SettingExternal adjustment activated via input S3
43160Number0255SettingExternal adjustment activated via input S2
43161Number0255SettingExternal adjustment activated via input S1
43163String0255SettingBlocking status of the shunt controlled add heat acc0=Unblocked, 1=Blocked
43164Number0255SettingCooling blocked
43171String0255SettingBlocking status of the step controlled add heat acc0=Unblocked, 1=Blocked
43189String0255SettingExt. Heat Medium Pump0=Off, 1=On
43230Number09999999SettingAccumulated energy
43239Number09999999SettingTot. HW op.time add.
43395Number0255SettingHPAC Relays
43416Number09999999SettingCompressor starts EB100-EP14
43420Number09999999SettingTot. op.time compr. EB100-EP14
43424Number09999999SettingTot. HW op.time compr. EB100-EP14
43427String0255SettingCompressor State EP1420=Stopped, 40=Starting, 60=Running, 100=Stopping
43431Number0255SettingSupply Pump State EP14
43433Number0255SettingBrine pump state EP14
43435String0255SettingCompressor status EP140=Off, 1=On
43437Number0255SettingHM-pump Status EP14
43439Number0255SettingBrinepump Status EP14
43473Number0255SettingHeat Compressors
43474Number0255SettingHot Water Compressors
43475Number0255SettingPool 1 Compressors
43484Number0255SettingFLM Cooling Activated
43485Number0255SettingFLM Cooling Activated
43486Number0255SettingFLM Cooling Activated
43487Number0255SettingFLM Cooling Activated
43514Number0255SettingPCA-Base Relays EP14
43516Number0255SettingPCA-Power Relays EP14
43560Number0255SettingPool 2 blocked
43561Number0255SettingPool 1 blocked
43563Number0255SettingPool 2 valve
43564Number0255SettingPool 1 valve
43577Number0255SettingPool 2 Compressors
43580Number065535SettingEB108 Version
43598Number0255SettingEB108 Slave Type
43599Number0255SettingEB108 Compressor Size
43600Number-3276732767SettingEB108-EP15-BT3 Return temp.
43601Number-3276732767SettingEB108-EP15-BT10 Brine in temp
43602Number-3276732767SettingEB108-EP15-BT11 Brine out temp
43603Number-3276732767SettingEB108-EP15-BT12 Cond. out
43604Number-3276732767SettingEB108-EP15-BT14 Hot gas temp
43605Number-3276732767SettingEB108-EP15-BT15 Liquid line
43606Number-3276732767SettingEB108-EP15-BT17 Suction
43607Number-3276732767SettingEB108-EP15-BT29 Compr. Oil. temp.
43608Number-3276732767SettingEB108-EP15-BP8 Pressure transmitter
43609Number0255SettingEB108-EP15 Compressor State
43610Number0255SettingEB108-EP15 Compr. time to start
43611Number065535SettingEB108-EP15 Relay status
43612Number0255SettingEB108-EP15 Heat med. pump status
43613Number0255SettingEB108-EP15 Brine pump status
43614Number04294967295SettingEB108-EP15 Compressor starts
43616Number04294967295SettingEB108-EP15 Tot. op.time compr
43618Number04294967295SettingEB108-EP15 Tot. HW op.time compr
43620Number065535SettingEB108-EP15 Alarm number
43621Number-3276732767SettingEB108-EP14-BT3 Return temp.
43622Number-3276732767SettingEB108-EP14-BT10 Brine in temp
43623Number-3276732767SettingEB108-EP14-BT11 Brine out temp
43624Number-3276732767SettingEB108-EP14-BT12 Cond. out
43625Number-3276732767SettingEB108-EP14-BT14 Hot gas temp
43626Number-3276732767SettingEB108-EP14-BT15 Liquid line
43627Number-3276732767SettingEB108-EP14-BT17 Suction
43628Number-3276732767SettingEB108-EP14-BT29 Compr. Oil. temp.
43629Number-3276732767SettingEB108-EP14-BP8 Pressure transmitter
43630Number0255SettingEB108-EP14 Compressor State
43631Number0255SettingEB108-EP14 Compr. time to start
43632Number065535SettingEB108-EP14 Relay status
43633Number0255SettingEB108-EP14 Heat med. pump status
43634Number0255SettingEB108-EP14 Brine pump status
43635Number09999999SettingEB108-EP14 Compressor starts
43637Number09999999SettingEB108-EP14 Tot. op.time compr
43639Number09999999SettingEB108-EP14 Tot. HW op.time compr
43641Number065535SettingEB108-EP14 Alarm number
43642Number065535SettingEB107 Version
43660Number0255SettingEB107 Slave Type
43661Number0255SettingEB107 Compressor Size
43662Number-3276732767SettingEB107-EP15-BT3 Return temp.
43663Number-3276732767SettingEB107-EP15-BT10 Brine in temp
43664Number-3276732767SettingEB107-EP15-BT11 Brine out temp
43665Number-3276732767SettingEB107-EP15-BT12 Cond. out
43666Number-3276732767SettingEB107-EP15-BT14 Hot gas temp
43667Number-3276732767SettingEB107-EP15-BT15 Liquid line
43668Number-3276732767SettingEB107-EP15-BT17 Suction
43669Number-3276732767SettingEB107-EP15-BT29 Compr. Oil. temp.
43670Number-3276732767SettingEB107-EP15-BP8 Pressure transmitter
43671Number0255SettingEB107-EP15 Compressor State
43672Number0255SettingEB107-EP15 Compr. time to start
43673Number065535SettingEB107-EP15 Relay status
43674Number0255SettingEB107-EP15 Heat med. pump status
43675Number0255SettingEB107-EP15 Brine pump status
43676Number04294967295SettingEB107-EP15 Compressor starts
43678Number04294967295SettingEB107-EP15 Tot. op.time compr
43680Number04294967295SettingEB107-EP15 Tot. HW op.time compr
43682Number065535SettingEB107-EP15 Alarm number
43683Number-3276732767SettingEB107-EP14-BT3 Return temp.
43684Number-3276732767SettingEB107-EP14-BT10 Brine in temp
43685Number-3276732767SettingEB107-EP14-BT11 Brine out temp
43686Number-3276732767SettingEB107-EP14-BT12 Cond. out
43687Number-3276732767SettingEB107-EP14-BT14 Hot gas temp
43688Number-3276732767SettingEB107-EP14-BT15 Liquid line
43689Number-3276732767SettingEB107-EP14-BT17 Suction
43690Number-3276732767SettingEB107-EP14-BT29 Compr. Oil. temp.
43691Number-3276732767SettingEB107-EP14-BP8 Pressure transmitter
43692Number0255SettingEB107-EP14 Compressor State
43693Number0255SettingEB107-EP14 Compr. time to start
43694Number065535SettingEB107-EP14 Relay status
43695Number0255SettingEB107-EP14 Heat med. pump status
43696Number0255SettingEB107-EP14 Brine pump status
43697Number09999999SettingEB107-EP14 Compressor starts
43699Number09999999SettingEB107-EP14 Tot. op.time compr
43701Number09999999SettingEB107-EP14 Tot. HW op.time compr
43703Number065535SettingEB107-EP14 Alarm number
43704Number065535SettingEB106 Version
43722Number0255SettingEB106 Slave Type
43723Number0255SettingEB106 Compressor Size
43724Number-3276732767SettingEB106-EP15-BT3 Return temp.
43725Number-3276732767SettingEB106-EP15-BT10 Brine in temp
43726Number-3276732767SettingEB106-EP15-BT11 Brine out temp
43727Number-3276732767SettingEB106-EP15-BT12 Cond. out
43728Number-3276732767SettingEB106-EP15-BT14 Hot gas temp
43729Number-3276732767SettingEB106-EP15-BT15 Liquid line
43730Number-3276732767SettingEB106-EP15-BT17 Suction
43731Number-3276732767SettingEB106-EP15-BT29 Compr. Oil. temp.
43732Number-3276732767SettingEB106-EP15-BP8 Pressure transmitter
43733Number0255SettingEB106-EP15 Compressor State
43734Number0255SettingEB106-EP15 Compr. time to start
43735Number065535SettingEB106-EP15 Relay status
43736Number0255SettingEB106-EP15 Heat med. pump status
43737Number0255SettingEB106-EP15 Brine pump status
43738Number04294967295SettingEB106-EP15 Compressor starts
43740Number04294967295SettingEB106-EP15 Tot. op.time compr
43742Number04294967295SettingEB106-EP15 Tot. HW op.time compr
43744Number065535SettingEB106-EP15 Alarm number
43745Number-3276732767SettingEB106-EP14-BT3 Return temp.
43746Number-3276732767SettingEB106-EP14-BT10 Brine in temp
43747Number-3276732767SettingEB106-EP14-BT11 Brine out temp
43748Number-3276732767SettingEB106-EP14-BT12 Cond. out
43749Number-3276732767SettingEB106-EP14-BT14 Hot gas temp
43750Number-3276732767SettingEB106-EP14-BT15 Liquid line
43751Number-3276732767SettingEB106-EP14-BT17 Suction
43752Number-3276732767SettingEB106-EP14-BT29 Compr. Oil. temp.
43753Number-3276732767SettingEB106-EP14-BP8 Pressure transmitter
43754Number0255SettingEB106-EP14 Compressor State
43755Number0255SettingEB106-EP14 Compr. time to start
43756Number065535SettingEB106-EP14 Relay status
43757Number0255SettingEB106-EP14 Heat med. pump status
43758Number0255SettingEB106-EP14 Brine pump status
43759Number09999999SettingEB106-EP14 Compressor starts
43761Number09999999SettingEB106-EP14 Tot. op.time compr
43763Number09999999SettingEB106-EP14 Tot. HW op.time compr
43765Number065535SettingEB106-EP14 Alarm number
43766Number065535SettingEB105 Version
43784Number0255SettingEB105 Slave Type
43785Number0255SettingEB105 Compressor Size
43786Number-3276732767SettingEB105-EP15-BT3 Return temp.
43787Number-3276732767SettingEB105-EP15-BT10 Brine in temp
43788Number-3276732767SettingEB105-EP15-BT11 Brine out temp
43789Number-3276732767SettingEB105-EP15-BT12 Cond. out
43790Number-3276732767SettingEB105-EP15-BT14 Hot gas temp
43791Number-3276732767SettingEB105-EP15-BT15 Liquid line
43792Number-3276732767SettingEB105-EP15-BT17 Suction
43793Number-3276732767SettingEB105-EP15-BT29 Compr. Oil. temp.
43794Number-3276732767SettingEB105-EP15-BP8 Pressure transmitter
43795Number0255SettingEB105-EP15 Compressor State
43796Number0255SettingEB105-EP15 Compr. time to start
43797Number065535SettingEB105-EP15 Relay status
43798Number0255SettingEB105-EP15 Heat med. pump status
43799Number0255SettingEB105-EP15 Brine pump status
43800Number04294967295SettingEB105-EP15 Compressor starts
43802Number04294967295SettingEB105-EP15 Tot. op.time compr
43804Number04294967295SettingEB105-EP15 Tot. HW op.time compr
43806Number065535SettingEB105-EP15 Alarm number
43807Number-3276732767SettingEB105-EP14-BT3 Return temp.
43808Number-3276732767SettingEB105-EP14-BT10 Brine in temp
43809Number-3276732767SettingEB105-EP14-BT11 Brine out temp
43810Number-3276732767SettingEB105-EP14-BT12 Cond. out
43811Number-3276732767SettingEB105-EP14-BT14 Hot gas temp
43812Number-3276732767SettingEB105-EP14-BT15 Liquid line
43813Number-3276732767SettingEB105-EP14-BT17 Suction
43814Number-3276732767SettingEB105-EP14-BT29 Compr. Oil. temp.
43815Number-3276732767SettingEB105-EP14-BP8 Pressure transmitter
43816Number0255SettingEB105-EP14 Compressor State
43817Number0255SettingEB105-EP14 Compr. time to start
43818Number065535SettingEB105-EP14 Relay status
43819Number0255SettingEB105-EP14 Heat med. pump status
43820Number0255SettingEB105-EP14 Brine pump status
43821Number09999999SettingEB105-EP14 Compressor starts
43823Number09999999SettingEB105-EP14 Tot. op.time compr
43825Number09999999SettingEB105-EP14 Tot. HW op.time compr
43827Number065535SettingEB105-EP14 Alarm number
43828Number065535SettingEB104 Version
43846Number0255SettingEB104 Slave Type
43847Number0255SettingEB104 Compressor Size
43848Number-3276732767SettingEB104-EP15-BT3 Return temp.
43849Number-3276732767SettingEB104-EP15-BT10 Brine in temp
43850Number-3276732767SettingEB104-EP15-BT11 Brine out temp
43851Number-3276732767SettingEB104-EP15-BT12 Cond. out
43852Number-3276732767SettingEB104-EP15-BT14 Hot gas temp
43853Number-3276732767SettingEB104-EP15-BT15 Liquid line
43854Number-3276732767SettingEB104-EP15-BT17 Suction
43855Number-3276732767SettingEB104-EP15-BT29 Compr. Oil. temp.
43856Number-3276732767SettingEB104-EP15-BP8 Pressure transmitter
43857Number0255SettingEB104-EP15 Compressor State
43858Number0255SettingEB104-EP15 Compr. time to start
43859Number065535SettingEB104-EP15 Relay status
43860Number0255SettingEB104-EP15 Heat med. pump status
43861Number0255SettingEB104-EP15 Brine pump status
43862Number04294967295SettingEB104-EP15 Compressor starts
43864Number04294967295SettingEB104-EP15 Tot. op.time compr
43866Number04294967295SettingEB104-EP15 Tot. HW op.time compr
43868Number065535SettingEB104-EP15 Alarm number
43869Number-3276732767SettingEB104-EP14-BT3 Return temp.
43870Number-3276732767SettingEB104-EP14-BT10 Brine in temp
43871Number-3276732767SettingEB104-EP14-BT11 Brine out temp
43872Number-3276732767SettingEB104-EP14-BT12 Cond. out
43873Number-3276732767SettingEB104-EP14-BT14 Hot gas temp
43874Number-3276732767SettingEB104-EP14-BT15 Liquid line
43875Number-3276732767SettingEB104-EP14-BT17 Suction
43876Number-3276732767SettingEB104-EP14-BT29 Compr. Oil. temp.
43877Number-3276732767SettingEB104-EP14-BP8 Pressure transmitter
43878Number0255SettingEB104-EP14 Compressor State
43879Number0255SettingEB104-EP14 Compr. time to start
43880Number065535SettingEB104-EP14 Relay status
43881Number0255SettingEB104-EP14 Heat med. pump status
43882Number0255SettingEB104-EP14 Brine pump status
43883Number09999999SettingEB104-EP14 Compressor starts
43885Number09999999SettingEB104-EP14 Tot. op.time compr
43887Number09999999SettingEB104-EP14 Tot. HW op.time compr
43889Number065535SettingEB104-EP14 Alarm number
43890Number065535SettingEB103 Version
43908Number0255SettingEB103 Slave Type
43909Number0255SettingEB103 Compressor Size
43910Number-3276732767SettingEB103-EP15-BT3 Return temp.
43911Number-3276732767SettingEB103-EP15-BT10 Brine in temp
43912Number-3276732767SettingEB103-EP15-BT11 Brine out temp
43913Number-3276732767SettingEB103-EP15-BT12 Cond. out
43914Number-3276732767SettingEB103-EP15-BT14 Hot gas temp
43915Number-3276732767SettingEB103-EP15-BT15 Liquid line
43916Number-3276732767SettingEB103-EP15-BT17 Suction
43917Number-3276732767SettingEB103-EP15-BT29 Compr. Oil. temp.
43918Number-3276732767SettingEB103-EP15-BP8 Pressure transmitter
43919Number0255SettingEB103-EP15 Compressor State
43920Number0255SettingEB103-EP15 Compr. time to start
43921Number065535SettingEB103-EP15 Relay status
43922Number0255SettingEB103-EP15 Heat med. pump status
43923Number0255SettingEB103-EP15 Brine pump status
43924Number04294967295SettingEB103-EP15 Compressor starts
43926Number04294967295SettingEB103-EP15 Tot. op.time compr
43928Number04294967295SettingEB103-EP15 Tot. HW op.time compr
43930Number065535SettingEB103-EP15 Alarm number
43931Number-3276732767SettingEB103-EP14-BT3 Return temp.
43932Number-3276732767SettingEB103-EP14-BT10 Brine in temp
43933Number-3276732767SettingEB103-EP14-BT11 Brine out temp
43934Number-3276732767SettingEB103-EP14-BT12 Cond. out
43935Number-3276732767SettingEB103-EP14-BT14 Hot gas temp
43936Number-3276732767SettingEB103-EP14-BT15 Liquid line
43937Number-3276732767SettingEB103-EP14-BT17 Suction
43938Number-3276732767SettingEB103-EP14-BT29 Compr. Oil. temp.
43939Number-3276732767SettingEB103-EP14-BP8 Pressure transmitter
43940Number0255SettingEB103-EP14 Compressor State
43941Number0255SettingEB103-EP14 Compr. time to start
43942Number065535SettingEB103-EP14 Relay status
43943Number0255SettingEB103-EP14 Heat med. pump status
43944Number0255SettingEB103-EP14 Brine pump status
43945Number09999999SettingEB103-EP14 Compressor starts
43947Number09999999SettingEB103-EP14 Tot. op.time compr
43949Number09999999SettingEB103-EP14 Tot. HW op.time compr
43951Number065535SettingEB103-EP14 Alarm number
43952Number065535SettingEB102 Version
43970Number0255SettingEB102 Slave Type
43971Number0255SettingEB102 Compressor Size
43972Number-3276732767SettingEB102-EP15-BT3 Return temp.
43973Number-3276732767SettingEB102-EP15-BT10 Brine in temp
43974Number-3276732767SettingEB102-EP15-BT11 Brine out temp
43975Number-3276732767SettingEB102-EP15-BT12 Cond. out
43976Number-3276732767SettingEB102-EP15-BT14 Hot gas temp
43977Number-3276732767SettingEB102-EP15-BT15 Liquid line
43978Number-3276732767SettingEB102-EP15-BT17 Suction
43979Number-3276732767SettingEB102-EP15-BT29 Compr. Oil. temp.
43980Number-3276732767SettingEB102-EP15-BP8 Pressure transmitter
43981Number0255SettingEB102-EP15 Compressor State
43982Number0255SettingEB102-EP15 Compr. time to start
43983Number065535SettingEB102-EP15 Relay status
43984Number0255SettingEB102-EP15 Heat med. pump status
43985Number0255SettingEB102-EP15 Brine pump status
43986Number04294967295SettingEB102-EP15 Compressor starts
43988Number04294967295SettingEB102-EP15 Tot. op.time compr
43990Number04294967295SettingEB102-EP15 Tot. HW op.time compr
43992Number065535SettingEB102-EP15 Alarm number
43993Number-3276732767SettingEB102-EP14-BT3 Return temp.
43994Number-3276732767SettingEB102-EP14-BT10 Brine in temp
43995Number-3276732767SettingEB102-EP14-BT11 Brine out temp
43996Number-3276732767SettingEB102-EP14-BT12 Cond. out
43997Number-3276732767SettingEB102-EP14-BT14 Hot gas temp
43998Number-3276732767SettingEB102-EP14-BT15 Liquid line
43999Number-3276732767SettingEB102-EP14-BT17 Suction
44000Number-3276732767SettingEB102-EP14-BT29 Compr. Oil. temp.
44001Number-3276732767SettingEB102-EP14-BP8 Pressure transmitter
44002Number0255SettingEB102-EP14 Compressor State
44003Number0255SettingEB102-EP14 Compr. time to start
44004Number065535SettingEB102-EP14 Relay status
44005Number0255SettingEB102-EP14 Heat med. pump status
44006Number0255SettingEB102-EP14 Brine pump status
44007Number09999999SettingEB102-EP14 Compressor starts
44009Number09999999SettingEB102-EP14 Tot. op.time compr
44011Number09999999SettingEB102-EP14 Tot. HW op.time compr
44013Number065535SettingEB102-EP14 Alarm number
44014Number065535SettingEB101 Version
44032Number0255SettingEB101 Slave Type
44033Number0255SettingEB101 Compressor Size
44034Number-3276732767SettingEB101-EP15-BT3 Return temp.
44035Number-3276732767SettingEB101-EP15-BT10 Brine in temp
44036Number-3276732767SettingEB101-EP15-BT11 Brine out temp
44037Number-3276732767SettingEB101-EP15-BT12 Cond. out
44038Number-3276732767SettingEB101-EP15-BT14 Hot gas temp
44039Number-3276732767SettingEB101-EP15-BT15 Liquid line
44040Number-3276732767SettingEB101-EP15-BT17 Suction
44041Number-3276732767SettingEB101-EP15-BT29 Compr. Oil. temp.
44042Number-3276732767SettingEB101-EP15-BP8 Pressure transmitter
44043Number0255SettingEB101-EP15 Compressor State
44044Number0255SettingEB101-EP15 Compr. time to start
44045Number065535SettingEB101-EP15 Relay status
44046Number0255SettingEB101-EP15 Heat med. pump status
44047Number0255SettingEB101-EP15 Brine pump status
44048Number04294967295SettingEB101-EP15 Compressor starts
44050Number04294967295SettingEB101-EP15 Tot. op.time compr
44052Number04294967295SettingEB101-EP15 Tot. HW op.time compr
44054Number065535SettingEB101-EP15 Alarm number
44055Number-3276732767SettingEB101-EP14-BT3 Return temp.
44056Number-3276732767SettingEB101-EP14-BT10 Brine in temp
44057Number-3276732767SettingEB101-EP14-BT11 Brine out temp
44058Number-3276732767SettingEB101-EP14-BT12 Cond. out
44059Number-3276732767SettingEB101-EP14-BT14 Hot gas temp
44060Number-3276732767SettingEB101-EP14-BT15 Liquid line
44061Number-3276732767SettingEB101-EP14-BT17 Suction
44062Number-3276732767SettingEB101-EP14-BT29 Compr. Oil. temp.
44063Number-3276732767SettingEB101-EP14-BP8 Pressure transmitter
44064Number0255SettingEB101-EP14 Compressor State
44065Number0255SettingEB101-EP14 Compr. time to start
44066Number065535SettingEB101-EP14 Relay status
44067Number0255SettingEB101-EP14 Heat med. pump status
44068Number0255SettingEB101-EP14 Brine pump status
44069Number09999999SettingEB101-EP14 Compressor starts
44071Number09999999SettingEB101-EP14 Tot. op.time compr
44073Number09999999SettingEB101-EP14 Tot. HW op.time compr
44075Number065535SettingEB101-EP14 Alarm number
44138String0255SettingEB108-EP15 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44139String0255SettingEB108-EP14 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44151String0255SettingEB107-EP15 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44152String0255SettingEB107-EP14 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44164String0255SettingEB106-EP15 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44165String0255SettingEB106-EP14 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44177String0255SettingEB105-EP15 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44178String0255SettingEB105-EP14 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44190String0255SettingEB104-EP15 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44191String0255SettingEB104-EP14 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44203String0255SettingEB103-EP15 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44204String0255SettingEB103-EP14 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44216String0255SettingEB102-EP15 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44217String0255SettingEB102-EP14 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44229String0255SettingEB101-EP15 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44230String0255SettingEB101-EP14 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44242String0255SettingEB100-EP15 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44243String0255SettingEB100-EP14 Prio0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44266Number-3000030000SettingCool Degree Minutes
44267Number-3276732767SettingCalc. Cooling Supply Temperature S4
44268Number-3276732767SettingCalc. Cooling Supply Temperature S3
44269Number-3276732767SettingCalc. Cooling Supply Temperature S2
44270Number-3276732767SettingCalc. Cooling Supply Temperature S1
44276Number0255SettingState ACS
44277Number0255SettingState ACS heatdump
44278Number0255SettingState ACS cooldump
44282Number0255SettingUsed cprs. HW
44283Number0255SettingUsed cprs. heat
44284Number0255SettingUsed cprs. pool 1
44285Number0255SettingUsed cprs. pool 2
44298Number09999999SettingAccumulated Energy HW Cpr and Add
44300Number09999999SettingAccumulated Energy Heat Cpr and Add
44302Number09999999SettingAccumulated Energy Cooling Cpr
44304Number09999999SettingAccumulated Energy Pool Cpr
44306Number09999999SettingAccumulated Energy HW Cpr
44308Number09999999SettingAccumulated Energy Heat Cpr
44320Number0255SettingUsed cprs. cool
44331Number0255SettingSoftware release
44380Number0255SettingExternal Compressors
44410Number0255SettingEB108 Own Hot Water
44411Number-3276732767SettingEB108-BT6 Hot water load temp.
44412Number-3276732767SettingEB108-BT7 Hot water top temp.
44413Number-3276732767SettingEB108-BT2 Supply temp.
44416Number0255SettingEB107 Own Hot Water
44417Number-3276732767SettingEB107-BT6 Hot water load temp.
44418Number-3276732767SettingEB107-BT7 Hot water top temp.
44419Number-3276732767SettingEB107-BT2 Supply temp.
44422Number0255SettingEB106 Own Hot Water
44423Number-3276732767SettingEB106-BT6 Hot water load temp.
44424Number-3276732767SettingEB106-BT7 Hot water top temp.
44425Number-3276732767SettingEB106-BT2 Supply temp.
44428Number0255SettingEB105 Own Hot Water
44429Number-3276732767SettingEB105-BT6 Hot water load temp.
44430Number-3276732767SettingEB105-BT7 Hot water top temp.
44431Number-3276732767SettingEB105-BT2 Supply temp.
44434Number0255SettingEB104 Own Hot Water
44435Number-3276732767SettingEB104-BT6 Hot water load temp.
44436Number-3276732767SettingEB104-BT7 Hot water top temp.
44437Number-3276732767SettingEB104-BT2 Supply temp.
44440Number0255SettingEB103 Own Hot Water
44441Number-3276732767SettingEB103-BT6 Hot water load temp.
44442Number-3276732767SettingEB103-BT7 Hot water top temp.
44443Number-3276732767SettingEB103-BT2 Supply temp.
44446Number0255SettingEB102 Own Hot Water
44447Number-3276732767SettingEB102-BT6 Hot water load temp.
44448Number-3276732767SettingEB102-BT7 Hot water top temp.
44449Number-3276732767SettingEB102-BT2 Supply temp.
44452Number0255SettingEB101 Own Hot Water
44453Number-3276732767SettingEB101-BT6 Hot water load temp.
44454Number-3276732767SettingEB101-BT7 Hot water top temp.
44455Number-3276732767SettingEB101-BT2 Supply temp.
44487Number0255SettingCool Compressors
44744Number0255SettingExtra heating system pump S4
44745Number0255SettingExtra heating system pump S3
44746Number0255SettingExtra heating system pump S2
44748Number0255SettingPool 2 pump
44749Number0255SettingPool 1 pump
44753Number0255SettingPassiv cool shunt
44754Number0255SettingPassiv cool pool
44756Number0255SettingState ground water pump
44874Number0255SettingState SG Ready
44878Number0255SettingSG Ready input A
44879Number0255SettingSG Ready input B
44910Number-3276732767SettingBrine pump dT act.
44911Number-3276732767SettingBrine pump dT act.
44912Switch01SensorBrine pump auto controlled
45001Number-3276732767SensorAlarm Number
47291Number010000SensorFloor drying timer
47325Number07SensorStep controlled add. max. step
47004Number015SensorHeat curve S4
47005Number015SensorHeat curve S3
47006Number015SensorHeat curve S2
47007Number015SensorHeat curve S1
47008Number-1010SensorOffset S4
47009Number-1010SensorOffset S3
47010Number-1010SensorOffset S2
47011Number-1010SensorOffset S1
47012Number50700SensorMin Supply System 4
47013Number50700SensorMin Supply System 3
47014Number50700SensorMin Supply System 2
47015Number50700SensorMin Supply System 1
47016Number50700SensorMax Supply System 4
47017Number50700SensorMax Supply System 3
47018Number50700SensorMax Supply System 2
47019Number50700SensorMax Supply System 1
47020Number080SensorOwn Curve P7
47021Number080SensorOwn Curve P6
47022Number080SensorOwn Curve P5
47023Number080SensorOwn Curve P4
47024Number080SensorOwn Curve P3
47025Number080SensorOwn Curve P2
47026Number080SensorOwn Curve P1
47027Number-4030SensorPoint offset outdoor temp.
47028Number-1010SensorPoint offset
47029Number-1010SensorExternal adjustment S4
47030Number-1010SensorExternal adjustment S3
47031Number-1010SensorExternal adjustment S2
47032Number-1010SensorExternal adjustment S1
47033Number50300SensorExternal adjustment with room sensor S4
47034Number50300SensorExternal adjustment with room sensor S3
47035Number50300SensorExternal adjustment with room sensor S2
47036Number50300SensorExternal adjustment with room sensor S1
47041String02SensorHot water mode0=Economy, 1=Normal, 2=Luxury
47043Number50700SensorStart temperature HW Luxury
47044Number50700SensorStart temperature HW Normal
47045Number50700SensorStart temperature HW Economy
47046Number550700SensorStop temperature Periodic HW
47047Number50700SensorStop temperature HW Luxury
47048Number50700SensorStop temperature HW Normal
47049Number50700SensorStop temperature HW Economy
47050Switch01SettingPeriodic HW
47051Number190SettingPeriodic HW Interval
47054Number160SettingRun time HWC
47055Number060SettingStill time HWC
47131String021SettingLanguage0=English, 1=Svenska, 2=Deutsch, 3=Francais, 4=Espanol, 5=Suomi, 6=Lietuviu, 7=Cesky, 8=Polski, 9=Nederlands, 10=Norsk, 11=Dansk, 12=Eesti, 13=Latviesu, 16=Magyar
47134Number0180SettingPeriod HW
47135Number0180SettingPeriod Heat
47136Number0180SettingPeriod Pool
47138String1040SettingOperational mode heat medium pump10=Intermittent, 20=Continous, 30=Economy, 40=Auto
47139String1030SettingOperational mode brine medium pump10=Intermittent, 20=Continuous, 30=Economy, 40=Auto
47206Number-1000-30SettingDM start heating
47207Number-3276732767SettingDM start cooling
47208Number-3276732767SettingDM start add.
47209Number-3276732767SettingDM between add. steps
47210Number-2000-30SettingDM start add. with shunt
47212Number04500SettingMax int add. power
47214Number1200SettingFuse
47261Number0100SettingExhaust Fan speed 4
47262Number0100SettingExhaust Fan speed 3
47263Number0100SettingExhaust Fan speed 2
47264Number0100SettingExhaust Fan speed 1
47265Number0100SettingExhaust Fan speed normal
47271Number199SettingFan return time 4
47272Number199SettingFan return time 3
47273Number199SettingFan return time 2
47274Number199SettingFan return time 1
47275Number124SettingFilter Reminder period
47276Switch01SettingFloor drying
47277Number030SettingFloor drying period 7
47278Number030SettingFloor drying period 6
47279Number030SettingFloor drying period 5
47280Number030SettingFloor drying period 4
47281Number030SettingFloor drying period 3
47282Number030SettingFloor drying period 2
47283Number030SettingFloor drying period 1
47284Number1570SettingFloor drying temp. 7
47285Number1570SettingFloor drying temp. 6
47286Number1570SettingFloor drying temp. 5
47287Number1570SettingFloor drying temp. 4
47288Number1570SettingFloor drying temp. 3
47289Number1570SettingFloor drying temp. 2
47290Number1570SettingFloor drying temp. 1
47302Switch01SettingClimate system 2 accessory
47303Switch01SettingClimate system 3 accessory
47304Switch01SettingClimate system 4 accessory
47305Number1100SettingClimate system 4 mixing valve amp.
47306Number1100SettingClimate system 3 mixing valve amp.
47307Number1100SettingClimate system 2 mixing valve amp.
47308Number10300SettingClimate system 4 shunt wait
47309Number10300SettingClimate system 3 shunt wait
47310Number10300SettingClimate system 2 shunt wait
47312Switch01SettingFLM pump
47313Number130SettingFLM defrost
47317Switch01SettingShunt controlled add. accessory
47318Number590SettingShunt controlled add. min. temp.
47319Number048SettingShunt controlled add. min. runtime
47320Number1100SettingShunt controlled add. mixing valve amp.
47321Number10300SettingShunt controlled add. mixing valve wait
47322Switch01SettingStep controlled add. accessory
47323Number-2000-30SettingStep controlled add. start DM
47324Number01000SettingStep controlled add. diff. DM
47326Switch01SettingStep controlled add. mode
47327Switch01SettingGround water pump accessory
47329Switch01SettingCooling 2-pipe accessory
47330Switch01SettingCooling 4-pipe accessory
47335Number048SettingTime betw. switch heat/cool
47336Number5100SettingHeat at room under temp.
47337Number5100SettingCool at room over temp.
47338Number1100SettingCooling mix. valve amp.
47339Number10300SettingCooling mix. valve step delay
47340Switch01SettingCooling with room sensor
47341Switch01SettingHPAC accessory
47342Number10500SettingStart Passive Cooling DM
47343Number30300SettingStart Active Cooling DM
47352Switch01SettingSMS40 accessory
47365Switch01SettingRMU System 1
47366Switch01SettingRMU System 2
47367Switch01SettingRMU System 3
47368Switch01SettingRMU System 4
47370Switch01SettingAllow Additive Heating
47371Switch01SettingAllow Heating
47372Switch01SettingAllow Cooling
47378Number10250SettingMax diff. comp.
47379Number10240SettingMax diff. add.
47380Switch01SettingLow brine out autoreset
47381Number-120150SettingLow brine out temp.
47382Switch01SettingHigh brine in
47383Number100300SettingHigh brine in temp.
47384String12SettingDate format1=DD-MM-YY, 2=YY-MM-DD
47385String1224SettingTime format12=hours 24, 24=Hours
47387Switch01SettingHW production12=hours 24, 24=Hours
47388Switch01SettingAlarm lower room temp.12=hours 24, 24=Hours
47389Switch01SettingAlarm lower HW temp.12=hours 24, 24=Hours
47391Switch01SettingUse room sensor S412=hours 24, 24=Hours
47392Switch01SettingUse room sensor S312=hours 24, 24=Hours
47393Switch01SettingUse room sensor S212=hours 24, 24=Hours
47394Switch01SettingUse room sensor S112=hours 24, 24=Hours
47395Number50300SettingRoom sensor setpoint S4
47396Number50300SettingRoom sensor setpoint S3
47397Number50300SettingRoom sensor setpoint S2
47398Number50300SettingRoom sensor setpoint S1
47399Number060SettingRoom sensor factor S4
47400Number060SettingRoom sensor factor S3
47401Number060SettingRoom sensor factor S2
47402Number060SettingRoom sensor factor S1
47413Number1100SettingSpeed circ.pump HW
47414Number1100SettingSpeed circ.pump Heat
47415Number7070SettingSpeed circ.pump Pool
47416Number0255SettingSpeed circ.pump Economy
47417Number1100SettingSpeed circ.pump Cooling
47418Number1100SettingSpeed brine pump
47537Switch01SettingNight cooling
47538Number2030SettingStart room temp. night cooling
47539Number310SettingNight Cooling Min. diff.
47540Number102000SettingHeat DM diff
47543Number10150SettingCooling DM diff
47570String0255SettingOperational mode0=Auto, 1=Manual, 2=Add. heat only
48053Number0100SettingFLM 2 speed 4
48054Number0100SettingFLM 2 speed 3
48055Number0100SettingFLM 2 speed 2
48056Number0100SettingFLM 2 speed 1
48057Number0100SettingFLM 2 speed normal
48058Number0100SettingFLM 3 speed 4
48059Number0100SettingFLM 3 speed 3
48060Number0100SettingFLM 3 speed 2
48061Number0100SettingFLM 3 speed 1
48062Number0100SettingFLM 3 speed normal
48063Number0100SettingFLM 4 speed 4
48064Number0100SettingFLM 4 speed 3
48065Number0100SettingFLM 4 speed 2
48066Number0100SettingFLM 4 speed 1
48067Number0100SettingFLM 4 speed normal
48068Switch01SettingFLM 4 accessory
48069Switch01SettingFLM 3 accessory
48070Switch01SettingFLM 2 accessory
48071Switch01SettingFLM 1 accessory
48072Number-3276732767SettingDM diff start add.
48073Switch01SettingFLM cooling
48074Number50400SettingSet point for BT74
48087Switch01SettingPool 2 accessory
48088Switch01SettingPool 1 accessory
48089Number50800SettingPool 2 start temp.
48090Number50800SettingPool 1 start temp.
48091Number50800SettingPool 2 stop temp.
48092Number50800SettingPool 1 stop temp.
48093Switch01SettingPool 2 Activated
48094Switch01SettingPool 1 Activated
48133Number0180SettingPeriod Pool 2
48174Number530SettingMin cooling supply temp S4
48175Number530SettingMin cooling supply temp S3
48176Number530SettingMin cooling supply temp S2
48177Number530SettingMin cooling supply temp S1
48178Number530SettingCooling supply temp. at 20°C
48179Number530SettingCooling supply temp. at 20°C
48180Number530SettingCooling supply temp. at 20°C
48181Number530SettingCooling supply temp. at 20°C
48182Number530SettingCooling supply temp. at 40°C
48183Number530SettingCooling supply temp. at 40°C
48184Number530SettingCooling supply temp. at 40°C
48185Number530SettingCooling supply temp. at 40°C
48186Switch01SettingCooling use mix. valves
48187Switch01SettingCooling use mix. valves
48188Switch01SettingCooling use mix. valves
48189Number0255SettingCooling use mix. valves
48190Number10500SettingHeatdump mix. valve delay
48191Number1100SettingHeatdump mix. valve amp.
48192Number10500SettingCooldump mix. valve delay
48193Number1100SettingCooldump mix. valve amp.
48194Switch01SettingACS accessory
48195Switch01SettingACS heat dump 24h-function
48196Switch01SettingACS run brinepump in wait mode
48197Number0100SettingACS closingtime for cool dump
48226Number80100SettingMax charge pump reg speed
48282Switch01SettingSG Ready heating
48283Switch01SettingSG Ready cooling
48284Switch01SettingSG Ready hot water
48285Switch01SettingSG Ready pool
48452Switch01SettingAuto heat medium pump speed, hw
48453Switch01SettingAuto heat medium pump speed, heat
48454Switch01SettingAuto heat medium pump speed, pool
48455Switch01SettingAuto heat medium pump speed, cool
48456Number1020SettingOperational mode heat medium pump, cooling
48458Number50100SettingMax speed circ.pump Heat
48459Number0100SettingSpeed brine pump cooling
48487Number1100SettingSpeed circ.pump Cooling